Skip to content

Yagi-Uda Antenna Design Calculator

Calculate Yagi-Uda antenna element lengths, gain, spacing, and impedance. Design directional Yagi antennas for any frequency. Free, instant results.

Empirical Yagi rules · G ≈ 10·log₁₀(0.8N) + 2.15 dBiAPI slug yagi-antenna

Sign in to saveSave
Example2 m band, 5 elements, 144 MHz
reflector 1.041 mdriven element 978.5 mmdirector 936.9 mms 416.4 mmboom 1.666 mf 144 MHzN 5
Operating frequency in MHz

1 MHz to 10 GHz

Total number of elements including reflector, driver, and directors

2 to 20

Formula

λ=c/f,G≈10⋅log⁡10(0.8⋅N)+2.15dBi,Lboom=(N−1)⋅0.2λ(c=299792458m/s)λ = c/f,\quad G ≈ 10·\operatorname{log}₁₀(0.8·N) + 2.15 \mathrm{dBi},\quad L_{boom} = (N − 1)·0.2λ (c = 299 792 458 m/s)
SymbolQuantityYour value
λWavelength (m)—
fFrequency (MHz)144 MHz
NNumber of elements5
GGain (dBi)+8.2 dBi
LboomBoom length the 0.2λ spacing implies (m)1.666 m

Assumptions

5 items
  1. 01Element lengths are fixed fractions of the free-space wavelength λ = c/f: reflector 0.50λ, driven element 0.47λ and every director 0.45λ, all spaced 0.2λ apart; element diameter, the boom-mounting correction and director tapering are not modelled.
  2. 02Gain is the empirical estimate G = 10·log10(0.8·N) + 2.15 dBi, which depends on the element count alone, not on the spacing or an optimised design.
  3. 03The feed impedance is a rough estimate, 73·(1 − 0.02·(N − 1)) Ω and not below 10 Ω, not a computed array impedance; no matching section is designed.
  4. 04The boom is the length the 0.2λ spacing implies, (N − 1)·0.2λ, reported as its own output; a boom of another length is not an input and does not change the gain estimate.
  5. 05The element count is rounded to a whole number from 2 to 20, and the antenna is in free space, with no ground or mast. Synthesis solves the frequency (1–10 000 MHz) numerically for a target driven-element length.

Worked example

A 7-element 70 cm Yagi with a 325 mm driven element

A 7-element Yagi's driven element measures 325 mm. Solving the frequency for that driver length gives 433.55 MHz, in the 70 cm band, and from it the other elements, their spacing and the gain estimate.

StepExpressionResult
Frequency the 325 mm driver is cut forf = 0.47 × 299.792458 m·MHz / 0.325 m433.55 MHz
Wavelengthλ = 299.792458 m·MHz / 433.546 MHz691.49 mm
Reflector0.50 × 691.49 mm345.7 mm
Each director0.45 × 691.49 mm311.2 mm
Element spacing0.2 × 691.49 mm138.3 mm
Boom the spacing implies(7 − 1) × 138.3 mm829.8 mm
Gain estimate10·log10(0.8 × 7) + 2.15+9.6 dBi

How it works

Yagi antenna calculator computes element lengths, spacing, and gain for directional arrays — amateur radio operators, TV broadcast engineers, and point-to-point wireless designers use Yagis for their excellent gain-to-size ratio. The design uses one driven element (fed directly), one reflector (5% longer, spaced 0.15-0.25 lambda behind), and multiple directors (3-5% shorter, spaced 0.1-0.35 lambda ahead), per Balanis's 'Antenna Theory' (4th ed.) and the classic DL6WU design tables.

Gain scales approximately as G = 10*log10(n) + 7 dBi for n elements with optimized spacing, achieving 6 dBd (8.15 dBi) for 3 elements, 9 dBd (11.15 dBi) for 6 elements, and 12 dBd (14.15 dBi) for 10+ elements. The driven element is typically a folded dipole (300 ohms) transformed to 50 ohms via 4:1 balun, or a split dipole with direct feed. Front-to-back ratio of 15-25 dB reduces interference from the rear.

Bandwidth is inversely related to element count: a 3-element Yagi covers approximately 5% bandwidth with VSWR < 2:1, while a 12-element design may have only 2% bandwidth. The log-periodic dipole array (LPDA) provides 3:1 or wider bandwidth at the cost of 3-6 dB lower gain than a Yagi of similar boom length. Yagi design requires careful optimization of element lengths and spacings — published designs (DL6WU, NBS, VK3AUU) provide proven starting points.

Practical tips

  • Start with proven designs (DL6WU, NBS, VK3AUU) rather than calculating from scratch — these have been optimized through simulation and field testing over decades
  • For receiving applications (SDR, weak-signal), longer Yagis with more directors provide better signal-to-noise despite narrower bandwidth; for transmitting, ensure full VSWR bandwidth coverage
  • Use 4NEC2 or EZNEC modeling software to optimize element dimensions for your specific materials (tube diameter, boom style) before construction

Common mistakes

  • Using theoretical dipole length (lambda/2) for driven element — parasitic coupling from reflector and directors lowers resonant length by 5-10%; always use published optimized designs or NEC simulation
  • Incorrect element spacing — spacing is more critical than length for gain; 0.1 lambda error in director spacing can reduce gain by 1-2 dB and shift resonant frequency 5%
  • Neglecting boom-to-element correction — conductive boom passing through elements acts as a parallel inductance, requiring 1-3% length reduction depending on boom diameter; insulated mounting eliminates this effect
  • Assuming equal director lengths — optimal designs use tapered director lengths, each progressively shorter; equal-length directors reduce gain by 1-2 dB versus optimized taper

Frequently asked questions

5 questions
What is the typical gain of a Yagi-Uda antenna?

Gain scales with element count per Balanis analysis: 2 elements: 5-6 dBi (reflector + driven only). 3 elements: 7-8 dBi. 5 elements: 10-11 dBi. 8 elements: 12-13 dBi. 12 elements: 14-15 dBi. 20+ elements: 16-17 dBi (practical limit due to losses). Gain increases approximately 1 dB per added director until diminishing returns around 10-12 elements. Boom length (not element count alone) determines gain: 1 lambda boom approximately equals 11 dBi; 2 lambda boom approximately equals 14 dBi.

Can Yagi-Uda antennas work for different frequencies?

A fixed Yagi operates over narrow bandwidth (2-5% typical). For different bands: (1) Build separate Yagis for each band. (2) Use interlaced Yagis on common boom (elements for different bands interleaved, with care to avoid interaction). (3) Use log-periodic dipole array (LPDA) for wide bandwidth (3:1 ratio) at cost of 3-6 dB less gain. (4) Active antenna selection via relay. Yagi elements scale inversely with frequency: a 144 MHz Yagi scaled to 432 MHz uses 1/3 dimensions but same electrical design.

Are Yagi-Uda antennas good for long-distance communication?

Yes — Yagis excel at point-to-point and weak-signal work due to high gain and directivity. Applications: Amateur radio EME (Earth-Moon-Earth): stacked 12+ element Yagis providing 20+ dBi. Amateur satellite: 8-12 element Yagis at 145/435 MHz with Az-El rotator. Point-to-point WiFi bridges: 2.4/5.8 GHz Yagis reaching 10+ km. TV reception: 10-15 element UHF Yagis for distant stations. Gain translates to range: 10 dBi Yagi versus dipole provides 10 dB link improvement, equivalent to 3.2x range increase in free space.

How do I calculate Yagi element dimensions?

Element lengths as fraction of wavelength (lambda = c/f): Reflector: 0.495*lambda (slightly longer than resonance). Driven element: 0.473*lambda (resonant at slightly higher frequency). Directors: 0.440-0.430*lambda (tapered shorter toward front). Spacings: Reflector to driven: 0.15-0.25*lambda. Driven to D1: 0.10-0.20*lambda. D_n to D_(n+1): 0.20-0.35*lambda, often increasing toward front. These ratios are starting points — use published optimized designs (DL6WU, NBS) or NEC modeling for best results. Element diameter affects length: thicker elements are shorter.

What is the difference between a Yagi and a log-periodic antenna?

Yagi: All elements coupled parasitically to single driven element; narrow bandwidth (2-5%); highest gain per boom length; requires retuning for different frequencies. LPDA: All elements active (connected to feedline via phased transmission line); wide bandwidth (3:1 to 10:1); 3-6 dB less gain than same-length Yagi; no retuning needed. Choose Yagi for maximum gain on single frequency (amateur, point-to-point). Choose LPDA for wide bandwidth with moderate gain (TV reception across UHF band, wideband monitoring, EMC testing).

References

Antenna Theory: Analysis and Design, 4th ed. · Antenna Theory and Design, 3rd ed.
  1. Antenna Theory: Analysis and Design, 4th ed. — Constantine A. Balanis (2016), Chapter 10 — Yagi-Uda array design
  2. Antenna Theory and Design, 3rd ed. — Warren L. Stutzman & Gary A. Thiele (2012), Chapter 5 — Yagi-Uda element spacing and gain

Shop Components

As an Amazon Associate we earn from qualifying purchases.

  • SMA Right-Angle ConnectorsEdge-mount and right-angle SMA connectors for antenna feedsAmazon →
  • RTL-SDR DongleWideband SDR receiver for antenna and signal experimentsAmazon →
  • Magnet Wire (22 AWG)Enameled copper wire for winding custom antennas and coilsAmazon →