RF Link Budget Calculator
Free RF link budget calculator: enter Tx power, antenna gains, frequency, and distance to get received signal level, link margin, and max range. Covers satellite, terrestrial, and IoT links.
Friis transmission equation · ITU-R P.525-4API slug rf-link-budget
Results
LiveLink Margin +23.4 dB
13.4 dB above your 10 dB target
- Free Space Path LossFSPL
- 100.1dB
- EIRPEIRP
- 32.0dBm
- Received PowerPᵣₓ
- −66.6dBm
- Max Rangedmax
- 14.87km
- Total Additional LossLtotal
- 0.5dB
- Range at Target Margindt
- 4.703km
- Wavelengthλ
- 124.9mm
- First Fresnel Zone Radiusr₁
- 5.588m
Received Power against Distance
Drag the operating point or type a value.
Formula
Friis, "A Note on a Simple Transmission Formula" (1946)
| Symbol | Quantity | Your value |
|---|---|---|
| d | Distance (m) | 1 km |
| λ | Wavelength (c/f) (m) | 124.9 mm |
| EIRP | Pₜₓ + Gₜₓ − Lₜₓ (dBm) | 32.0 dBm |
| Pᵣₓ | EIRP − FSPL − L_rain − L_atm − L_pt − ΣLₙ + Gᵣₓ − Lᵣₓ (dBm) | −66.6 dBm |
| Lrain | Rain fade (ITU-R P.838) (dB) | 0.0 dB |
| Latm | Atmospheric / gaseous absorption (dB) | 0.5 dB |
| Lpt | Antenna pointing / misalignment loss (dB) | 0.0 dB |
Assumptions
8 items
- 01Free space. The path loss is the Friis loss 20·log10(4πd/λ) over an unobstructed line of sight; ground reflection, diffraction, vegetation, multipath and clutter are not modelled.
- 02Far field. The antennas are separated by much more than 2D²/λ; at very short range the formula would show a gain, which is not physical.
- 03λ = c/f with c = 299 792 458 m/s.
- 04Aligned, co-polarised antennas. Gains are peak values in dBi; misalignment and polarisation mismatch count only through the pointing-loss term.
- 05Rain fade, atmospheric loss and pointing loss are whole-path totals in dB, not rates per kilometre, so they do not grow with distance, including in the maximum range.
- 06Extra loss terms (up to four) add to the whole-path losses: use them for vegetation, body, polarisation or any other loss you can put a number on.
- 07Cable loss is entered per end: the TX cable loss reduces EIRP, and the RX cable loss is subtracted after the receive antenna gain.
- 08Link margin is received power minus receiver sensitivity. PASS means the margin meets your target (10 dB by default, typical for a fixed link); CHECK means between 0 dB and the target; FAIL means below 0 dB. Maximum range is the distance at which the margin falls to 0 dB with every other input unchanged.
Worked example
LoRa node, 915 MHz, 10 km rural
A LoRa node on a mast transmits 20 dBm at 915 MHz through 2 dB of cable and a 6 dBi antenna to a 3 dBi handheld receiver 10 km away, through 6 dB of vegetation. The receiver runs SF12 at 125 kHz, with −137 dBm sensitivity, and the link should keep a 20 dB fade margin.
| Step | Expression | Result |
|---|---|---|
| Path loss | 20·log10(4π × 10 km × 915 MHz / 299 792 458 m/s) | 111.7 dB |
| EIRP | 20 + 6 − 2 | 24.0 dBm |
| Received power | 24.00 − 111.68 − 6 + 3 − 0 | −90.7 dBm |
| Link margin | −90.68 − (−137) | +46.3 dB |
| Against the 20 dB target | 46.32 − 20 | +26.3 dB |
| Range at the 20 dB target | 2 071 × 10^(−20 / 20) | 207.1 km |
How it works
RF link budget analysis calculates received signal power in wireless systems — telecommunications engineers, satellite system designers, and IoT developers use this to determine if a radio link will close with adequate margin. The Friis transmission equation P_rx = P_tx + G_tx + G_rx - FSPL - L_misc forms the foundation, where FSPL = 20*log10(4*pi*d*f/c) per ITU-R P.525-4.
Free-space path loss increases 6 dB per doubling of distance (inverse-square law) and 6 dB per doubling of frequency. At 2.4 GHz and 1 km, FSPL = 100.1 dB; at 5.8 GHz and 1 km, FSPL = 107.7 dB. This explains why 5 GHz WiFi has shorter range than 2.4 GHz given identical transmit power. According to Skolnik's 'Radar Handbook' (3rd ed.), atmospheric absorption adds 0.01 dB/km at 2 GHz but 0.2 dB/km at 60 GHz (oxygen resonance). Link margin = P_rx - P_sensitivity represents safety buffer against fading. ITU-R P.530-17 recommends 25-40 dB fade margin for 99.999% availability microwave links. For mobile systems, Rayleigh fading causes 20-30 dB signal variation — LTE systems design for 8-12 dB margin with power control. GPS receivers operate at -130 dBm sensitivity with 25+ dB link margin to ensure global coverage.Why engineers pick a link budget calculator over full RF simulation software
Commercial RF design environments — Keysight ADS, Cadence AWR, Ansys HFSS — excel at 3D electromagnetic simulation and nonlinear circuit analysis, but a link budget is fundamentally algebra on a spreadsheet. Every dB is additive. The real bottleneck for teams running link budgets is iteration speed: tweaking distance, frequency, or antenna gain and seeing the margin update immediately. A browser-based calculator with URL-shareable scenarios covers 90% of budgeting work in under 10 seconds per iteration; commercial tools are reserved for the 10% that requires co-simulation with modulation, coding, or propagation raytracing.
When to use this calculator vs. a full propagation model
This tool uses the Friis free-space model (ITU-R P.525-4) plus user-supplied atmospheric/rain/pointing loss terms. It is the correct choice when you need (a) a first-order sanity check before detailed design, (b) quick comparison between frequency bands or antenna gains, (c) order-of-magnitude range estimation for IoT/LPWAN deployments, or (d) teaching the Friis equation. For pathloss in cluttered environments, layer in Okumura-Hata (150 MHz – 1.5 GHz urban), COST-231 Hata (1.5 – 2 GHz), or ITU-R P.1411 (short-range urban) before trusting the margin number.
Practical tips
- Design for 10-15 dB link margin minimum for fixed wireless; 20-30 dB for mobile systems subject to multipath fading; 30-40 dB for critical infrastructure (ITU-R P.530)
- Use ITU-R propagation models appropriate to environment: P.525 (free space), P.1411 (urban), P.833 (vegetation), P.676 (atmospheric), P.838 (rain attenuation)
- Validate link budget predictions with drive testing or site survey — actual propagation often differs 5-15 dB from models due to local terrain and building effects
- Copy the scenario URL (toolbar button) and paste it into design review notes — it round-trips every input so reviewers run the exact same calculation
- For iterative trade studies, pair this calculator with the Noise Figure Cascade calculator to see how front-end LNA gain and noise figure change the effective sensitivity number
Common mistakes
- Using free-space path loss for terrestrial links without environmental corrections — add 10-30 dB for urban environments (ITU-R P.1411), 6-15 dB for suburban, 3-6 dB for rural with vegetation per ITU-R P.833
- Neglecting cable and connector losses — a 30m LMR-400 run at 2.4 GHz loses 3.5 dB; four N connectors add 0.6 dB; total 4.1 dB often omitted from link budgets
- Confusing antenna gain with EIRP — transmit power + antenna gain = EIRP; regulatory limits (FCC Part 15) typically specify EIRP, not transmit power alone
- Ignoring frequency-dependent atmospheric absorption — negligible below 10 GHz but critical at 60 GHz (15 dB/km) and 24 GHz (0.2 dB/km) per ITU-R P.676
- Using straight-line horizontal distance for satellite or elevated links — slant range matters. At 30° elevation to a 500 km LEO satellite, slant range is ~900 km — nearly twice the altitude. Under-estimating slant range under-estimates FSPL by 3–6 dB.
- Forgetting polarization loss on mobile or tumbling platforms — a fixed linear ground antenna receiving from a spacecraft with arbitrary orientation loses up to 3 dB on average, not zero
Frequently asked questions
13 questions
What does dBm represent?
dBm is power referenced to 1 milliwatt: P(dBm) = 10*log10(P_mW). Common values: 0 dBm = 1 mW, 10 dBm = 10 mW, 20 dBm = 100 mW, 30 dBm = 1 W. Receiver sensitivities are typically negative: -100 dBm = 0.1 pW (WiFi), -130 dBm = 0.1 fW (GPS). The dBm scale allows link budget arithmetic by simple addition/subtraction rather than multiplication/division of power levels.
How does frequency impact path loss?
Free-space path loss increases 20*log10(f2/f1) dB when frequency increases from f1 to f2. Doubling frequency adds 6 dB loss. At 1 km: 433 MHz = 85.2 dB FSPL; 915 MHz = 91.7 dB; 2.4 GHz = 100.1 dB; 5.8 GHz = 107.7 dB. This 22.5 dB difference between 433 MHz and 5.8 GHz explains why sub-GHz IoT protocols (LoRa, Sigfox) achieve much longer range than WiFi for the same transmit power.
Can I use this calculator for non-free space environments?
This calculator provides theoretical free-space baseline per ITU-R P.525. For real environments, add empirical loss factors: Indoor office: +20 to +40 dB (walls, floors); Urban outdoor: +20 to +30 dB (buildings, vehicles); Suburban: +10 to +20 dB; Rural open: +3 to +10 dB (vegetation, terrain). For detailed modeling, use Okumura-Hata (150 MHz-1.5 GHz urban), COST-231 (1.5-2 GHz), or ray-tracing for specific building layouts.
What's the typical acceptable received signal strength?
Depends on modulation and bandwidth. WiFi (OFDM, 20 MHz BW): -65 dBm excellent, -75 dBm good, -85 dBm marginal. Cellular LTE: -80 dBm excellent, -100 dBm usable. LoRa (SF12, 125 kHz): -137 dBm sensitivity. GPS: -130 dBm nominal. Bluetooth: -70 dBm excellent, -90 dBm usable. The 60+ dB difference between WiFi and LoRa sensitivity explains the range/throughput tradeoff — LoRa achieves 15 km at 300 bps while WiFi reaches 100m at 100 Mbps.
How do antenna gains impact link budget?
Antenna gain directly adds to link budget: +3 dBi = doubles range (for constant sensitivity) because 6 dB path loss equals 2x distance. A 24 dBi parabolic dish provides 24 dB more link budget than a 0 dBi omni — equivalent to reducing path loss from 1 km to 60m, or increasing transmit power 250x. High-gain antennas trade coverage area for range: a 24 dBi dish has 10-degree beamwidth requiring precise alignment.
How do I calculate the range of my 433 MHz LoRa node?
Link budget approach: Available path loss = P_tx + G_tx + G_rx - P_sensitivity - margin. Example: 20 dBm transmit, 2 dBi antennas each side, -137 dBm sensitivity (SF12), 20 dB margin = 20 + 2 + 2 - (-137) - 20 = 141 dB allowable FSPL. Solve FSPL = 20*log10(d) + 20*log10(433e6) - 147.55 = 141 dB for d = 618 km theoretical. Real-world with terrain: 10-30 km rural, 2-5 km suburban, 0.5-2 km urban. The sub-GHz advantage: same calculation at 2.4 GHz yields only 112 km theoretical due to 15 dB higher FSPL.
What fade margin should I add to a microwave link budget?
ITU-R P.530-17 defines fade margin requirements by availability: 99.9% availability: 15-20 dB margin; 99.99%: 25-30 dB; 99.999%: 35-40 dB. Margin accounts for multipath fading, rain attenuation (significant above 10 GHz), equipment aging, and atmospheric variations. For a 10 km, 18 GHz link in temperate climate: 15 dB multipath + 8 dB rain (0.01% exceedance) + 3 dB equipment = 26 dB total margin for 99.99% availability.
How much does antenna height affect link range?
Antenna height affects Fresnel zone clearance, not free-space loss directly. First Fresnel zone radius at mid-path: r1 = sqrt(lambda * d/4). For 10 km link at 5.8 GHz: r1 = sqrt(0.052 * 2500) = 11m. If terrain obstructs > 40% of this zone, add 6+ dB diffraction loss. Height determines whether the Fresnel zone is clear — insufficient clearance is the most common cause of link failures in point-to-point systems. Rule of thumb: antenna height should provide r1 clearance above any obstacles at mid-path.
What's the difference between link margin and fade margin?
Link margin = P_received - P_sensitivity (total safety buffer). Fade margin is the portion reserved for signal fading events. Example: 30 dB link margin might allocate: 20 dB fade margin (multipath, rain), 5 dB implementation margin (component tolerance, aging), 5 dB interference margin. Fade margin determines availability statistics — 20 dB fade margin with Rayleigh fading yields approximately 99.9% availability per ITU-R P.530. Under-specifying fade margin is the leading cause of intermittent link failures.
Is this RF link budget calculator free?
Yes — every feature on this page is free, runs in your browser, and requires no signup. Scenarios round-trip through URL parameters, so sharing a design with a colleague is just a copy-paste. Pro and API tiers exist for cloud-saved scenarios, batch calculation via REST, and advanced async simulations (Monte Carlo, Touchstone export), but link budget math itself is always free.
How does this compare to commercial RF link budget software like AGI/STK, MATLAB, or VisualSat?
This calculator implements the Friis + ITU-R P.525 free-space model with user-supplied atmospheric/rain/pointing loss terms — roughly equivalent to a commercial tool's first-pass budget worksheet. Commercial packages add: time-varying satellite geometry (AGI STK Cloud, until sunset March 2026), full propagation raytracing with terrain databases, integrated modulation performance (BER vs. Eb/No curves), and regulatory compliance reporting. For iterative design and teaching, the browser-based approach is faster; for operational mission planning, the commercial tools earn their license cost. rftools.io also ships an async Satellite Link Budget tool (/tools/sat-link-budget) that adds preset orbits, AMSAT CSV export, and ITU-R P.618 rain models for the gap between the two categories.
Can I export my link budget to a report or to Touchstone / MATLAB?
Yes. Every calculator has a Card export (shareable 1200x630 PNG with the scenario embedded) and CSV/BOM exporters. For S-parameter–compatible formats, use the RF Cascade tool (/tools/rf-cascade), which accepts per-stage Touchstone .s2p uploads and exports combined .sNp. For Python or MATLAB pipelines, the Pro API (/docs/api) serves JSON results over /api/py/v1/calculate — same math, automatable.
Why is my calculated max range much longer than what I actually achieve in the field?
Max range here assumes free-space propagation — no obstructions, no multipath, no interference, no Fresnel-zone intrusion. Real environments typically introduce 10-30 dB additional loss vs. the model, which cuts range by 3-30x depending on terrain. For realistic field estimates, either (a) add an environment loss term into 'atmospheric loss' matching your scenario (see the 'non-free space' FAQ above) or (b) use a two-ray ground-bounce model for terrestrial links near ground.
References
A Note on a Simple Transmission Formula · ITU-R P.525-4 · ITU-R P.618-13
- A Note on a Simple Transmission Formula — Harald T. Friis, Proc. IRE 34(5), pp. 254–256 (1946)
- ITU-R P.525-4 — Calculation of free-space attenuation
- ITU-R P.618-13 — Rain and atmospheric attenuation for Earth-space links
- Microwave Engineering, 4th ed. — David M. Pozar (2011), Chapter 14 — Wireless Communication Systems
Shop Components
As an Amazon Associate we earn from qualifying purchases.