Skip to content

LC Filter Calculator — Low-Pass, High-Pass & Band-Pass

Design passive Butterworth and Chebyshev LC ladder filters up to order 10. Calculate component values for low-pass, high-pass, and band-pass topologies. Free, instant results.

LC ladder prototype g-values · Butterworth and 0.5 dB ChebyshevAPI slug filter-designer

Sign in to saveSave

Specification

Example

Butterworth is maximally flat; Chebyshev Type I trades 0.5 dB of passband ripple for a steeper rolloff

The design frequency: the −3 dB point of a Butterworth, the edge of the 0.5 dB ripple band of a Chebyshev, the centre of a band-pass

1 Hz to 1 GHz

Filter order (1–10). Higher orders give steeper rolloff: n × 20 dB/decade.

1 to 10

Source/load impedance. 50 Ω is standard for RF systems; 600 Ω for audio.

1 Ω to 10 kΩ

Higher Q = narrower bandwidth. Used only by the band-pass filter type.

0.1 to 100

Rounds every part to the nearest value in the series; the response and the export are the rounded design's.

Circuit

Values shown: Ideal
50 ΩC14.502 µFL2 11.25 mH50 Ω
RefPositiongₖIdeal
C1Shunt1.4144.502µF
L2Series1.41411.25mH

Response

Ideal
−3.0 dB at 1 kHz−12.3 dB at 2 kHz−60−50−40−30−20−100100 Hz1 kHz10 kHzdB
Passband detail
−3.5−3−2.5−2−1.5−1−0.50500 Hz1 kHzdB
Cutoff as Built (−3 dB)
1kHz
Worst Passband Loss
1.5dB
Stopband Loss as Built
12.3dB
Time Constant ττ
0ns
Attenuation at 2×fcA(2fc)
12.3dB
BandwidthBW
0Hz
Lower −3 dB FrequencyfL
0Hz
Upper −3 dB FrequencyfH
0Hz
Max Component ErrorEmax
0.0%PASS
Cutoff ShiftΔfc
0.0%
Load ImpedanceRL
50Ω

Formula

Williams & Taylor, Electronic Filter Design Handbook 4th ed.; Zverev, Handbook of Filter Synthesis
Ck=gkωc⋅Z0,Lk=gk⋅Z0ωcC_k = \frac{g_k}{\omega_c \cdot Z_0},\quad L_k = \frac{g_k \cdot Z_0}{\omega_c}
SymbolQuantityYour value
gkNormalized prototype element value (Butterworth or Chebyshev)—
ωcAngular cutoff frequency (2πf_c) (rad/s)—
Z₀Characteristic impedance (Ω)50 Ω
τRC time constant (s)0 ns
fcCutoff frequency (Hz)1 kHz
QQuality factor1
nFilter order (1–10)2

Assumptions

6 items
  1. 01A doubly terminated LC ladder built from the low-pass prototype values g_k, computed in closed form for orders 1 to 10: Butterworth g_k = 2·sin((2k − 1)π/2n), or Chebyshev Type I with 0.5 dB of ripple, the only ripple offered (Pozar Eq. 8.73); the low-pass is denormalised as a shunt C = g_k/(ω_c·Z₀) and a series L = g_k·Z₀/ω_c, alternately, starting with the C.
  2. 02The high-pass is the series-first ladder transformed, a series C = 1/(ω_c·g_k·Z₀) and a shunt L = Z₀/(ω_c·g_k); the band-pass turns each element into a resonator tuned to f_c with fractional bandwidth Δ = 1/Q, a shunt C = g_k/(ω₀·Δ·Z₀) in parallel with its L and a series L = g_k·Z₀/(ω₀·Δ) in series with its C.
  3. 03Source and load are both Z₀, except an even-order Chebyshev, whose ladder needs a load of Z₀/1.9841 (1.9841·Z₀ after the high-pass's series first element); the load output gives it and a warning says so.
  4. 04The parts are ideal, with no loss and no parasitics, so inductor Q, capacitor ESR and self-resonance are not modelled; f_c (1 Hz to 1 GHz) is the −3 dB point of a Butterworth, the edge of a Chebyshev's ripple band and the centre of a band-pass, whose bandwidth is f_c/Q, split evenly about f_c in the f_L and f_H outputs.
  5. 05The attenuation at 2·f_c is the prototype's, 10·log10(1 + 2^(2n)) for Butterworth and 10·log10(1 + ε²·T_n(2)²) with ε² = 10^(0.5/10) − 1 for Chebyshev; the time constant 1/ω_c is given for a first-order Butterworth only.
  6. 06With a part series chosen, every part is rounded to the nearest value of that series, and the response (the −3 dB frequency or band edges, the worst passband loss and the loss where the prototype reaches 2·f_c, all solved on the ladder between Z₀ and its load) and the KiCad export are the rounded design's; the cutoff shift compares the rounded ladder's −3 dB point with the ideal ladder's.

Worked example

100 MHz harmonic low-pass from E24 parts

A VHF transmitter needs a 5th-order Butterworth low-pass with its cutoff at 100 MHz in 50 Ω, built from E24 capacitors and inductors. What are the parts, and how far do the rounded values move the cutoff and the loss at 200 MHz?

StepExpressionResult
Second harmonic, where the loss is checked2 × 100 MHz200 MHz
C₁ = C₅, ideal2·sin(π/(2 × 5)) / (2π × 100 MHz × 50 Ω)19.67 pF
L₂ = L₄, ideal2·sin(3π/(2 × 5)) × 50 Ω / (2π × 100 MHz)128.8 nH
C₃, ideal2·sin(5π/(2 × 5)) / (2π × 100 MHz × 50 Ω)63.66 pF
C₁ = C₅ in E24E24(19.67 pF)20 pF
L₂ = L₄ in E24E24(128.8 nH)130 nH
C₃ in E24E24(63.66 pF)62 pF
Largest rounding error(63.66 pF − 62 pF) / 63.66 pF × 1002.6 %
Cutoff of the E24 ladder|S₂₁(f)|² = ½100.997 MHz
Cutoff shift100.997 MHz / 100 MHz − 1+1.0 %
Ideal loss at the second harmonic10·log10(1 + 2^(2 × 5))30.1 dB
Loss at 200 MHz as built−20·log10|S₂₁(200 MHz)|30.2 dB

How it works

The Filter Designer Calculator computes component values for Butterworth and Chebyshev analog filters — essential for anti-aliasing, signal conditioning, and EMI filtering applications. Analog designers, audio engineers, and RF specialists use this to create lowpass, highpass, and bandpass filters with predictable frequency response. Per Williams & Taylor 'Electronic Filter Design Handbook' (4th ed., McGraw-Hill) and Zverev's 'Handbook of Filter Synthesis' (Wiley, 1967), Butterworth filters achieve maximally flat passband with -20N dB/decade rolloff, where N = filter order. Filter design follows ITU-R recommendations for bandpass specifications and IEEE Standard 1241-2010 (IEEE Standard for Terminology and Test Methods for Analog-to-Digital Converters) for anti-aliasing filter requirements. A 5th-order Butterworth provides 100 dB attenuation at 10x cutoff frequency. Chebyshev filters trade passband ripple (0.5-3 dB typical) for steeper rolloff — a 5th-order Chebyshev 0.5 dB achieves same attenuation as 7th-order Butterworth. Per Zverev "Handbook of Filter Synthesis," normalized g-values enable direct component calculation: L = g*R/(2*pi*fc), C = g/(2*pi*fc*R). Even-order Chebyshev filters need unequal terminations: with 0.5 dB ripple g(N+1) = 1.9841, so the low-pass and band-pass ladders here (shunt element first) need a load of Z0/1.9841 and the high-pass ladder (series element first) a load of 1.9841*Z0.

Practical tips

  • Per Williams, use 1% tolerance components for filters requiring < 0.5 dB passband accuracy
  • Simulate in SPICE before building — component parasitics shift actual response from ideal
  • For high-Q bandpass filters (Q > 10), consider active topologies to avoid impractical inductor values
  • Cascade 2nd-order sections for orders > 3 to reduce component sensitivity per Analog Devices MT-210

Common mistakes

  • Neglecting component tolerances — 5% capacitor tolerance shifts fc by +/-5%; use 1% for critical applications per Williams
  • Failing to account for op-amp bandwidth — GBW must exceed 10x fc for active filter accuracy per TI AN-779
  • Overlooking parasitic inductance — 10 nH lead inductance causes 1% impedance error above 100 kHz

Frequently asked questions

6 questions
What makes Butterworth filters unique?

Maximally flat passband — no ripple, monotonic rolloff per Butterworth (1930). Transfer function magnitude |H(jw)|^2 = 1/(1+(w/wc)^2N). At cutoff, attenuation is exactly -3.01 dB. Rolloff is -20N dB/decade. Per Zverev, Butterworth minimizes in-band amplitude distortion at cost of slower rolloff vs. Chebyshev.

How do I choose between 1st and 2nd order filters?

1st-order: -20 dB/decade, 45 deg phase shift at fc. 2nd-order: -40 dB/decade, 90 deg at fc. Per Williams, 2nd-order provides 60 dB rejection at 30x fc vs. only 30 dB for 1st-order. Use 2nd-order minimum for anti-aliasing; 4th-6th order typical for production systems.

How do I choose between Butterworth and Chebyshev filter types?

Per Williams: Butterworth for passband flatness (audio, wideband amps) — 0 dB ripple. Chebyshev for sharp cutoff (anti-aliasing, interference rejection) — 0.5 dB ripple achieves equivalent of +2 Butterworth orders. 5th-order 0.5 dB Chebyshev matches 7th-order Butterworth rolloff while using 30% fewer components.

What order filter do I need to reject a signal 40 dB below my passband edge?

Per Zverev formula: N_Butterworth = log(10^(40/10)-1)/(2*log(fs/fc)). At 2x fc: N = 6.6 -> use 7th order. At 3x fc: N = 4.2 -> use 5th order. Chebyshev 0.5 dB needs N-2 orders less for same rejection. Use the stopband/passband frequency ratio to minimize filter order.

Why does my bandpass filter have worse insertion loss than designed?

Per Williams: (1) Inductor Q limits passband insertion loss — Q=50 inductor causes 0.1 dB loss per pole. (2) Narrow bandwidth (BW/fc < 10%) requires Q > 10 inductors rarely available in standard values. (3) 5% component tolerance causes +/-0.5 dB passband ripple. (4) Use Monte Carlo analysis — this site's RF filter tool simulates 1000 tolerance combinations.

Can Butterworth filters be cascaded?

Yes — cascading Nth-order sections yields N*M total order. Per Sedra & Smith, cascade identical 2nd-order sections for even orders; add 1st-order for odd orders. Total rolloff = -20*(N*M) dB/decade. Cascading simplifies component selection and reduces sensitivity to tolerance variations.

Shop Components

As an Amazon Associate we earn from qualifying purchases.

  • Op-Amp IC AssortmentGeneral-purpose and precision operational amplifiersAmazon →
  • Function GeneratorDDS function generator for signal and filter testingAmazon →