Skip to content

Half-Wave Dipole Antenna Calculator

Calculate dipole antenna length for any frequency — enter MHz, get half-wave and quarter-wave dimensions in mm. Includes gain (2.15 dBi), radiation resistance (73 Ω), and 50 Ω VSWR. Supports velocity factor for insulated wire.

Ideal thin half-wave dipole · L = v_f·c/(2f) · 73.1 Ω, 2.15 dBiAPI slug dipole-antenna

Sign in to saveSave
Example
feedL 335.8 mmL/2 167.9 mmf 433 MHzVF 0.97
Operating frequency in MHz

1 MHz to 6 GHz

Free space ≈ 0.97; with insulation ~0.95

0.5 to 1

Formula

Balanis, "Antenna Theory: Analysis and Design", 4th ed., Chapter 4
Lλ/2=vf⋅c2f,Zin≈73.1 Ω,G=2.15 dBiL_{\lambda/2} = \frac{v_f \cdot c}{2f}, \quad Z_{in} \approx 73.1\,\Omega, \quad G = 2.15\,\text{dBi}
SymbolQuantityYour value
Lλ/2Half-wave dipole total length (m)335.8 mm
vfVelocity factor of the wire—
cSpeed of light (299 792 458 m/s) (m/s)—
fOperating frequency (Hz)433 MHz
ZinInput impedance (radiation resistance) (Ω)73.1 Ω
GAntenna gain (dBi)+2.1 dBi

Assumptions

6 items
  1. 01The total length is L = VF·λ/2 with λ = c/f and c = 299 792 458 m/s; the velocity factor (0.97 by default) stands in for the end effect of real wire and for insulation, and no wire diameter or separate end correction is applied.
  2. 02Each arm is half the total, L/2, which is also the length of a quarter-wave monopole at the same velocity factor.
  3. 03Gain (2.15 dBi) and input impedance (73.1 Ω) are the constants of an ideal thin, centre-fed half-wave dipole in free space; they do not change with frequency or velocity factor, and the reactance of a dipole cut longer or shorter than resonance is not computed.
  4. 04The VSWR is that 73.1 Ω fed directly from 50 Ω coax with no matching network or balun, |Γ| = 23.1/123.1, so it always reads 1.46:1.
  5. 05Height above ground, nearby objects, the feed line and the mounting are not modelled.
  6. 06Synthesis solves the frequency (1–6000 MHz) or the velocity factor (0.5–1) numerically for a target half-wave length, within each input's range.

Worked example

A 1 m wire dipole on the 2 m band

A dipole has been cut to 1 m overall from bare wire, velocity factor 0.97. Solving the frequency for a half-wave length of 1 000 mm shows where it resonates: 145.40 MHz, inside the 2 m amateur band.

StepExpressionResult
Frequency the 1 000 mm dipole resonates atf = 0.97 × 299 792 458 m/s / (2 × 1 m)145.40 MHz
Free-space wavelengthλ = 299 792 458 m/s / 145.399 MHz2.062 m
Half-wave length0.97 × 2.062 m / 21 m
Each arm1 m / 2500 mm
VSWR on 50 Ω coax|Γ| = (73.1 − 50) / (73.1 + 50); (1 + |Γ|) / (1 − |Γ|)1.462:1

How it works

Dipole antenna calculator computes resonant length, feed impedance, and bandwidth for any frequency — antenna engineers, amateur radio operators, and wireless system designers use this to design practical antennas and establish the gain reference (dBd). A center-fed conductor exactly lambda/2 long resonates with 73.1 ohms radiation resistance and 2.15 dBi gain (0 dBd by definition), per Balanis's 'Antenna Theory: Analysis and Design' (4th ed.) and IEEE Standard 145-2013.

The physical length L = 0.95 * lambda/2 = 142.5/f_MHz meters accounts for end effects that make resonant length 5% shorter than free-space half wavelength. Radiation pattern is omnidirectional in the H-plane (perpendicular to antenna axis) with figure-eight pattern in the E-plane (along antenna axis), providing maximum radiation broadside to the element. Bandwidth (VSWR < 2:1) is approximately 5-10% of center frequency for typical wire dipoles.

Feed impedance at resonance is 73.1 + j0 ohms in free space per Kraus's 'Antennas' (3rd ed.). Height above ground affects impedance: at lambda/4 height, impedance drops to 50-60 ohms (better match to 50-ohm coax); at lambda/2 height, impedance rises to 85-100 ohms. Folded dipoles (300 ohms) are used with ladder line or 4:1 baluns. The dipole's simplicity, predictable characteristics, and well-documented behavior make it the starting point for all antenna education.

Practical tips

  • For quick deployment, cut elements 3% long and trim to resonance — it's easier to shorten than lengthen; use antenna analyzer or VNA to find minimum VSWR point
  • Mount horizontally for horizontal polarization (typical for VHF/UHF weak-signal work) or as inverted-V (apex up, 90-120 degree included angle) for broader coverage and easier single-support installation
  • For multiband operation, use fan dipole (multiple dipole pairs from same feedpoint) or trap dipole — resonant traps isolate sections for different bands

Common mistakes

  • Using free-space lambda/2 without end-effect correction — resonant length is 95% of theoretical due to capacitive loading at wire ends; a 2.4 GHz dipole cut at 62.5 mm will resonate at 2.28 GHz, not 2.4 GHz
  • Omitting balun causing feedline radiation — coax outer conductor carries common-mode current that radiates, distorting pattern and causing RF in the shack; always use a 1:1 current choke balun
  • Ignoring ground proximity effects — a dipole at 0.1 lambda height has 50% lower radiation resistance and distorted pattern; mount at least lambda/4 above ground for predictable performance
  • Expecting perfect 50-ohm match — resonant dipole is 73 ohms; VSWR 1.46:1 is normal and acceptable; forcing exact 50 ohms with matching network adds loss and complexity

Frequently asked questions

7 questions
How does antenna length change with frequency?

Inversely proportional: L = 142.5/f_MHz meters for half-wave dipole with end-effect correction. At 7 MHz (40m band): L = 20.4 m. At 144 MHz (2m): L = 0.99 m. At 2.4 GHz (WiFi): L = 59 mm. Higher frequencies mean shorter, more compact antennas. The 142.5 constant (approximately c/2 * 0.95) accounts for the 5% shortening from end capacitance. For different wire diameters, constant varies 140-146: thicker conductors have more end effect.

Why is 73.1 ohms the typical radiation resistance?

The 73.1-ohm value derives from solving Maxwell's equations for a thin, perfectly conducting, center-fed half-wave antenna in free space per Balanis analysis. It represents the real part of feed impedance at resonance where the reactive component is zero. This is NOT a design choice but a fundamental electromagnetic property. Variations occur: folded dipole = 292 ohms (4x), off-center feed increases impedance, proximity to ground changes value. The 73 ohms is close enough to 50 and 75 ohm standards that direct coax connection is practical.

Can I use a half-wave dipole for multiple frequencies?

A simple dipole is inherently narrowband (5-10% bandwidth). Multi-frequency options: (1) Fan dipole: multiple dipole pairs cut for different bands, fed from single point — elements must be separated to avoid interaction. (2) Trap dipole: resonant traps (LC circuits) isolate sections; outer section resonates lower band when trap opens at higher frequencies. (3) Multiband dipole with tuner: use antenna tuner to match, accepting efficiency loss from non-resonant operation. (4) Off-center-fed dipole (Windom): 1/3-2/3 feed point provides resonance at fundamental and third harmonic. Best efficiency: dedicated single-band dipoles.

What does 2.15 dBi gain mean?

2.15 dBi is the maximum gain of a half-wave dipole relative to an isotropic radiator (hypothetical point source radiating equally in all directions). Since isotropic antennas cannot physically exist, the dipole serves as the practical reference — gain relative to a dipole is expressed in dBd, where 0 dBd = 2.15 dBi. An antenna with 8.15 dBi gain has 6 dBd gain (6 dB better than dipole). The 2.15 dB difference comes from the dipole's figure-eight pattern concentrating energy broadside to the wire versus isotropic's uniform sphere.

How long should a dipole antenna be for 144 MHz?

Using the standard formula L = 142.5/f_MHz: L = 142.5/144 = 0.990 m total (99.0 cm), or 49.5 cm per element. For 12 AWG wire: use 143/144 = 99.3 cm. For 1/2-inch aluminum tubing: use 141/144 = 97.9 cm. Start 2-3% long (102 cm) and trim while measuring VSWR. Mount at least 50 cm above ground (lambda/4) for proper impedance. With 1:1 balun to 50-ohm coax, expect VSWR 1.3-1.5:1 at resonance without additional matching.

Why is dipole impedance 73 ohms instead of 50 ohms?

73 ohms is the electromagnetic reality of a resonant half-wave dipole per Maxwell's equations — it's physics, not design. The 50-ohm coax standard evolved from transmission line tradeoffs (compromise between minimum loss at 77 ohms and maximum power at 30 ohms). Solutions: (1) Accept 1.46:1 VSWR with direct connection (0.18 dB mismatch loss — negligible). (2) Cut dipole slightly short of resonance for 50-55 ohm impedance with small capacitive reactance. (3) Use lambda/4 matching section of 60-ohm coax (RG-62). (4) Use a 4:1 balun with folded dipole (292 ohms / 4 = 73 ohms). For most applications, direct connection with 1:1 balun is sufficient.

How do I build a 2-meter dipole for an SDR?

Simple construction for 144-148 MHz: (1) Cut two 49.5 cm pieces of stiff copper wire or aluminum rod. (2) Mount on center insulator with SO-239, BNC, or direct solder to coax. (3) Add 1:1 current balun: wind 6-8 turns of feedline coax (RG-58 or RG-174) on a 5-6 cm diameter form, or use 10 ferrite beads on coax. (4) Mount horizontally or as inverted-V at 120-degree angle. (5) Tune by trimming 5 mm at a time to minimize VSWR at 146 MHz. For SDR receive-only: balun is optional but improves pattern; add LNA at antenna for best weak-signal performance. Total cost: under $10 in materials.

References

Antenna Theory: Analysis and Design, 4th ed. · Antenna Theory and Design, 3rd ed.
  1. Antenna Theory: Analysis and Design, 4th ed. — Constantine A. Balanis (2016), Chapter 4 — Dipole antenna radiation resistance and gain
  2. Antenna Theory and Design, 3rd ed. — Warren L. Stutzman & Gary A. Thiele (2012), Chapter 3 — Wire antenna analysis

Shop Components

As an Amazon Associate we earn from qualifying purchases.

  • SMA Right-Angle ConnectorsEdge-mount and right-angle SMA connectors for antenna feedsAmazon →
  • RTL-SDR DongleWideband SDR receiver for antenna and signal experimentsAmazon →
  • Magnet Wire (22 AWG)Enameled copper wire for winding custom antennas and coilsAmazon →