Microstrip Patch Antenna Calculator
Calculate rectangular microstrip patch antenna dimensions (width, length) using the Transmission Line Model. Outputs effective dielectric constant, edge-feed impedance, and nominal gain for common substrates like FR4 and Rogers.
Transmission-line model · Hammerstad ΔL · Balanis slot conductances G₁ + G₁₂ · cos² inset feedAPI slug patch-antenna
Formula
Balanis, "Antenna Theory: Analysis and Design", 4th ed., Chapter 14: slot conductances §14.2, Eqs. (14-12), (14-17) and (14-18a), Examples 14.1–14.3; inset feed §14.2.1, Eq. (14-20a)
| Symbol | Quantity | Your value |
|---|---|---|
| W | Patch width (m) | 37.23 mm |
| L | Patch length (m) | 28.81 mm |
| εr | Substrate relative permittivity | 4.4 |
| εreff | Effective relative permittivity | 4.081 |
| ΔL | End-effect fringing extension (m) | — |
| c | Speed of light (299 792 458 m/s) (m/s) | — |
| f | Operating frequency (Hz) | 2.45 GHz |
| y₀ | Feed inset from the radiating edge (m) | 0 mm |
| Rin | Input resistance at the inset y₀ (Ω) | 321 Ω |
| G₁ | Self-conductance of one radiating slot (S) | — |
| G₁₂ | Mutual conductance between the two slots (S) | — |
Assumptions
5 items
- 01Transmission-line model (Balanis, chapter 14): W = c/(2f)·√(2/(εr + 1)), εeff = (εr + 1)/2 + (εr − 1)/2·(1 + 12h/W)^−0.5 at that width, the fringing extension ΔL from Hammerstad's formula, and L = c/(2f·√εeff) − 2ΔL, with c = 299 792 458 m/s; it is quasi-static and assumes a substrate much thinner than a wavelength.
- 02The width is the design width for the frequency, not an input, so solving the frequency or the substrate height for a target length assumes the patch is that width; synthesis solves either numerically within its range (0.1–100 GHz, 0.1–10 mm), and the material picker sets εr to the laminate's design Dk.
- 03The edge resistance is R_in = 1/(2(G₁ + G₁₂)), from the self and mutual conductances of the two radiating slots (Balanis, section 14.2), integrated numerically with η₀ = µ₀·c; it is lossless and not clamped, so an air patch reads its own value.
- 04An inset feed y₀ in from the radiating edge sees R_in·cos²(π·y₀/L) (Balanis Eq. 14-20a), and the inset that gives 50 Ω is reported where the edge resistance is above 50 Ω; the notch's own effect on the resonance is not modelled.
- 05The gain is a fixed 7.0 dBi, typical of a single patch; substrate and copper loss, the ground plane's size, surface waves and bandwidth are not modelled.
Worked example
Where does a 31 mm patch on RO4350B resonate?
A patch has been milled 31 mm long on 1.524 mm Rogers RO4350B, design Dk 3.66. Solving the frequency for that length shows where it resonates: 2.495 GHz, above the 2.4 GHz ISM band, so a 2.45 GHz patch on this laminate must be cut slightly longer.
| Step | Expression | Result |
|---|---|---|
| Frequency the 31 mm patch resonates at | L(f) = 31 mm ⇒ f | 2.495 GHz |
| Patch width at that frequency | 299.792458 / (2 × 2.49478) × √(2 / (3.66 + 1)) | 39.36 mm |
| Effective permittivity | (3.66 + 1) / 2 + (3.66 − 1) / (2 × √(1 + 12 × 1.524 / 39.36)) | 3.429 |
| Fringing extension ΔL at each end | 0.412 × 1.524 × (3.429 + 0.3) × (39.36 / 1.524 + 0.264) / ((3.429 − 0.258) × (39.36 / 1.524 + 0.8)) | 0.7235 mm |
| Length, less the fringing at both ends | 299.792458 / (2 × 2.49478 × √3.429) − 2 × 0.7235 | 31 mm |
| Resistance at the radiating edge | 1 / (2 × (G₁ + G₁₂)) | 292 Ω |
| Inset for 50 Ω | (31 / π) × acos(√(50 / 292)) | 11.29 mm |
How it works
Patch antenna calculator computes resonant length, width, feed position, and bandwidth for microstrip patch antennas on any PCB substrate — wireless device engineers, GPS receiver designers, and phased array architects use this to design low-profile integrated radiators and scalable arrays. The rectangular patch resonates when its length L approximately equals lambda_eff/2, where lambda_eff = lambda_0/sqrt(epsilon_eff) accounts for the substrate's effective dielectric constant, per Balanis's 'Antenna Theory' (4th ed.) and Pozar's 'Microwave Engineering'.
Patch dimensions for 50-ohm edge feed: width W = c/(2*f*sqrt((epsilon_r+1)/2)) provides good radiation efficiency (typically 90%+); length L = c/(2*f*sqrt(epsilon_eff)) - 2*delta_L corrects for fringing fields at radiating edges, where delta_L approximately equals 0.412*h*(epsilon_eff+0.3)*(W/h+0.264)/((epsilon_eff-0.258)*(W/h+0.8)). For FR-4 (epsilon_r = 4.4) at 2.4 GHz: W approximately equals 38 mm, L approximately equals 29 mm.
Bandwidth is inherently narrow: BW = (VSWR-1)/(Q*sqrt(VSWR)) where Q approximately equals c*sqrt(epsilon_eff)/(4*f*h). Typical 1.6 mm FR-4 patch at 2.4 GHz has Q approximately equals 30 and 2% bandwidth (48 MHz). Thicker substrates and lower epsilon_r increase bandwidth: 3.2 mm Rogers RO4003 (epsilon_r = 3.55) achieves 5% bandwidth. Gain is typically 6-9 dBi for single elements, increasing 3 dB per doubling of array elements.
Practical tips
- For prototyping, design patch 5% larger than calculated and trim with razor blade while monitoring S11 on VNA — much faster than iterating PCB fabrication
- Use coaxial probe feed for narrow bandwidth applications (simpler) or aperture coupling for wider bandwidth (more complex but better performance)
- For arrays, space elements 0.5-0.7 lambda_0 center-to-center to balance gain, sidelobe level, and mutual coupling — closer spacing increases coupling, wider spacing creates grating lobes
Common mistakes
- Ignoring effective dielectric constant — using epsilon_r directly gives wrong resonant length; epsilon_eff is always lower than epsilon_r due to fringing fields in air above substrate
- Neglecting substrate loss in efficiency calculation — FR-4 (tan_delta = 0.02) limits radiation efficiency to 80-90%; PTFE substrates (tan_delta < 0.001) achieve > 95% efficiency
- Using thin substrates for wideband applications — 0.8 mm substrate has Q approximately equals 80 (1% BW); need 3.2+ mm substrate for 5%+ bandwidth suitable for WiFi bands
- Expecting accurate resonant frequency from formulas alone — manufacturing tolerances in epsilon_r (+/-5%) and h (+/-10%) cause 2-5% frequency shift; always include tuning margin in design
Frequently asked questions
5 questions
What determines a microstrip patch antenna's bandwidth?
Bandwidth is inversely proportional to Q factor, which scales as Q approximately equals epsilon_r^(3/2)/(h/lambda_0). Three factors increase bandwidth: (1) Thicker substrate — doubling h approximately doubles bandwidth. (2) Lower dielectric constant — foam (epsilon_r = 1.1) provides 3x bandwidth of FR-4 (epsilon_r = 4.4). (3) Lower epsilon_r — also increases patch size. Typical bandwidth: 1-2% for 1.6 mm FR-4, 3-5% for 3 mm Rogers, 10-15% for stacked patch or U-slot designs. For WiFi (100 MHz BW at 2.4 GHz = 4%), use 3+ mm low-loss substrate.
Can I use this calculator for different frequency bands?
Yes — the transmission line model is frequency-independent. Key scaling: patch dimensions scale inversely with frequency. At 5.8 GHz versus 2.4 GHz: dimensions shrink by 2.4x. At 915 MHz versus 2.4 GHz: dimensions grow by 2.6x. Practical limits: at 5.8 GHz, patch is approximately 12 mm on FR-4 (easy to fabricate); at 915 MHz, patch is approximately 85 mm (may need air-dielectric for manageable size). Above 10 GHz, tight fabrication tolerances require +/-0.1 mm etching accuracy.
How accurate are these theoretical calculations?
Transmission line model provides +/-5% resonant frequency accuracy per Balanis. Error sources: (1) Dielectric constant variation: FR-4 is 4.0-4.8 depending on glass content and resin — get actual value from laminate datasheet. (2) Fringing field approximation: accurate for W/h > 1, less accurate for narrow patches. (3) Substrate thickness tolerance: +/-10% typical for 1.6 mm FR-4. For production, simulate with 3D EM solver (HFSS, CST) before fabrication. For prototypes, design with 5% tuning margin and iterate.
What feeding methods work best for microstrip patch antennas?
Common feeds ranked by complexity and performance: (1) Microstrip line edge feed: simplest, narrow bandwidth, poor for thick substrates due to surface wave. (2) Inset feed: direct 50-ohm match by insetting feed line into patch; most common for single-layer designs. (3) Coaxial probe: drills through substrate to patch interior; best for thick substrates but narrow bandwidth. (4) Aperture coupling: two-layer design with slot in ground plane; widest bandwidth (10%+), best isolation, most complex. (5) Proximity coupling: two-layer with no galvanic connection; good bandwidth, moderate complexity. For WiFi/Bluetooth, inset feed on single-layer is standard practice.
How do I improve my antenna's gain?
Single patch gain is limited to 6-9 dBi by aperture size. Improvement options: (1) Array: each doubling of elements adds 3 dB. 2x2 array = +6 dB. 4x4 array = +12 dB. (2) Larger patch on lower-epsilon substrate: increases aperture but also resonant frequency. (3) Stacked patches: parasitic element above driven patch increases gain 1-2 dB and bandwidth. (4) Reflector plane at lambda/4 spacing: adds 3 dB but increases profile. (5) Higher-efficiency substrate: Rogers RO4003 (tan_delta = 0.0027) versus FR-4 (tan_delta = 0.02) adds 0.5-1 dB. For maximum gain, use array on low-loss substrate with proper corporate feed network design.
References
Antenna Theory: Analysis and Design, 4th ed. · Antenna Theory: Analysis and Design, 4th ed. · Microstrip Antenna Design Handbook
- Antenna Theory: Analysis and Design, 4th ed. — Constantine A. Balanis (2016), Chapter 14 — Microstrip patch antenna transmission-line model
- Antenna Theory: Analysis and Design, 4th ed. — Constantine A. Balanis (2016), §14.2.1, Eq. (14-20a) and Fig. 14.11 — resonant input resistance of an inset (recessed) feed, R_in(y₀) = R_in(0)·cos²(πy₀/L)
- Microstrip Antenna Design Handbook — R. Garg, P. Bhartia, I. Bahl & A. Ittipiboon, Artech House (2001), Chapter 3 — Patch dimensions
Shop Components
As an Amazon Associate we earn from qualifying purchases.