Microstrip Impedance Calculator
Calculate microstrip impedance using Hammerstad-Jensen equations. Get Z0, effective dielectric constant, and propagation delay for PCB trace design. Free, instant results.
Quasi-static Hammerstad–Jensen (1980) model with η₀/2π and its own thickness correctionAPI slug microstrip-impedance
Formula
Hammerstad & Jensen (1980); Wadell, "Transmission Line Design Handbook" 1991
| Symbol | Quantity | Your value |
|---|---|---|
| η₀ | Impedance of free space, µ₀·c = 376.730 Ω (η₀/2π = 59.9585 Ω) (Ω) | — |
| u | Effective width/height ratio (W/H) | — |
| εeff | Effective dielectric constant | 2.95 |
| F | Hammerstad-Jensen correction factor | — |
Assumptions
6 items
- 01Quasi-static Hammerstad–Jensen (1980) closed forms for Z₀ and εeff, with the free-space impedance η₀ = µ₀·c (η₀/2π = 59.958 Ω), quasi-TEM with no dispersion: the frequency sets only the guided wavelength, λg = c/(f·√εeff), and Z₀ does not depend on it.
- 02Bare microstrip: air above the trace and no soldermask, on one homogeneous, non-magnetic substrate of permittivity εr over a solid ground plane that extends well beyond the trace.
- 03Copper thickness T enters by Hammerstad and Jensen’s 1980 correction: the trace widens by Δu₁ = (T/πH)·ln(1 + 4e/((T/H)·coth²√(6.517u))) in air and by Δuᵣ = ½(1 + sech√(εr − 1))·Δu₁ with the dielectric, within 0.5 % of rftools.io’s field solver for T/H up to 0.35; the trace is a rectangle, so an etched trapezoid is not modelled.
- 04Lossless: conductor and dielectric loss are neglected, so Z₀ is real and the delay is √εeff/c with c = 299.792458 mm/ns.
- 05Hammerstad and Jensen fitted their forms to about 1 % over 0.05 ≤ W/H ≤ 20 and εr up to about 12; outside that range this calculator still returns a result, without a warning.
- 06Synthesis solves the trace width (0.01–50 mm) or the substrate height (0.05–10 mm) numerically for the target Z₀. The material picker sets εr to the laminate’s design Dk (RO4350B 3.66, RO4003C 3.55); FR-4’s 4.4 is a typical value, not one product’s.
Worked example
50 Ω microstrip on 0.508 mm RO4350B
A 2.4 GHz board uses 0.508 mm (20 mil) RO4350B, design Dk 3.66, with 35 µm (1 oz) copper. Starting from that stack, solve the trace width for Z₀ = 50 Ω, then read the effective permittivity and the quarter-wave length it gives.
| Step | Expression | Result |
|---|---|---|
| Trace width for 50 Ω (solved) | Z₀(W) = 50 Ω; H = 0.508 mm, εr = 3.66, T = 35 µm | 1.0734 mm |
| Width ratio u | 1.0734 / 0.508 | 2.1129 |
| Width the copper adds in air, Δu₁ | 0.035 / (π × 0.508) × ln(1 + 4 × exp(1) × tanh(√(6.517 × 2.1129))² × 0.508 / 0.035) | 0.1111 |
| Width the copper adds with the dielectric, Δuᵣ | ½ × (1 + 1/cosh(√(3.66 − 1))) × 0.1111 | 0.07649 |
| Corrected width ratio uᵣ = u + Δuᵣ | 2.1129 + 0.07649 | 2.1894 |
| Hammerstad–Jensen exponent a(uᵣ) | 1 + ln((2.1894⁴ + (2.1894/52)²)/(2.1894⁴ + 0.432))/49 + ln(1 + (2.1894/18.1)³)/18.7 | 0.9997 |
| Hammerstad–Jensen exponent b(εr) | 0.564 × ((3.66 − 0.9)/(3.66 + 3))^0.053 | 0.5383 |
| Effective permittivity of the strip at uᵣ, εe(uᵣ) | (3.66 + 1)/2 + (3.66 − 1)/2 × (1 + 10/2.1894)^(−0.9997 × 0.5383) | 2.8580 |
| Hammerstad–Jensen F(uᵣ) | 6 + (2π − 6) × exp(−(30.666/2.1894)^0.7528) | 6.0002 |
| Characteristic impedance | 59.958/√2.8580 × ln(6.0002/2.1894 + √(1 + 4/2.1894²)) | 50 Ω |
| Width ratio in air, u₁ = u + Δu₁ | 2.1129 + 0.1111 | 2.2240 |
| Hammerstad–Jensen F(u₁) | 6 + (2π − 6) × exp(−(30.666/2.2240)^0.7528) | 6.0002 |
| Effective permittivity | 2.8580 × (ln(6.0002/2.2240 + √(1 + 4/2.2240²)) / ln(6.0002/2.1894 + √(1 + 4/2.1894²)))² | 2.806 |
| Quarter wave at 2.4 GHz | 299.792458/(2.4 × √2.806)/4 | 18.64 mm |
How it works
Microstrip impedance calculator computes characteristic impedance (Z0) and effective dielectric constant for PCB transmission lines using the Hammerstad-Jensen method — RF circuit designers and PCB layout engineers use this to design impedance-matched traces that minimize signal reflections. The Hammerstad-Jensen equations are derived from E. Hammerstad and O. Jensen, 'Accurate Models for Microstrip Computer-Aided Design', IEEE MTT-S International Microwave Symposium Digest (1980), and are the basis for IPC-2141A (Controlled Impedance Circuit Boards and High Speed Logic Design) and IPC-2251 (Design Guide for the Packaging of High Speed Electronic Circuits). Reference impedance standards are maintained by IEEE Standard 287-2007 and described in Pozar's 'Microwave Engineering' (4th ed.) Chapter 3. The Hammerstad-Jensen method mathematically models the complex electromagnetic interactions between a conductive trace and its substrate. These equations account for the non-uniform current distribution and fringing effects that occur when electromagnetic waves propagate along a printed circuit board trace. The characteristic impedance (Z0) depends critically on the trace geometry and dielectric properties, with key parameters including trace width, substrate height, dielectric constant, and copper thickness. By precisely calculating these interactions, engineers can design impedance-matched transmission lines that minimize signal reflections, reduce electromagnetic interference, and maintain signal integrity in high-frequency applications ranging from telecommunications to high-speed digital circuits.
Practical tips
- Always verify calculated impedance with actual measurement using vector network analyzer
- Consider temperature and frequency coefficients when designing precision RF circuits
- Use precision PCB fabrication techniques to maintain tight geometric tolerances
Common mistakes
- Neglecting copper surface roughness effects on high-frequency signal propagation
- Assuming ideal rectangular trace cross-sections without accounting for manufacturing tolerances
- Overlooking frequency-dependent dielectric constant variations
Frequently asked questions
10 questions
What is the typical impedance range for microstrip transmission lines?
Microstrip transmission lines commonly range from 25 to 100 ohms, with 50 ohms being the most standard impedance for RF and telecommunications applications.
How do substrate properties affect microstrip impedance?
Substrate dielectric constant, height, and copper thickness directly influence the characteristic impedance, with higher dielectric constants and thinner substrates typically resulting in lower impedance values.
Can microstrip impedance be calculated manually?
While possible, manual calculation is complex and error-prone. Modern engineering software and specialized calculators provide more accurate and efficient impedance determination.
What factors cause microstrip impedance variations?
Manufacturing tolerances, substrate material variations, temperature changes, and frequency dependencies can all introduce impedance variations in microstrip transmission lines.
Are Hammerstad-Jensen equations universally applicable?
These equations work well for standard PCB materials and geometries but may require modifications for extreme substrate configurations or very high frequencies.
How do I calculate microstrip impedance for a 4-layer FR-4 stackup?
For a typical 4-layer FR-4 stackup (e.g., 1.6 mm total, ~0.36 mm to inner ground plane), set substrateHeight to your dielectric thickness (e.g., 0.36 mm), dielectricConstant to 4.2–4.5 (check your laminate datasheet), and adjust traceWidth until you hit 50 Ω. A starting guess for 50 Ω on 0.36 mm FR-4 is ~0.7 mm. Most PCB fabs offer controlled-impedance services — give them your target and stack-up and they'll confirm the etched width.
Why does my microstrip impedance calculation differ from my PCB fab's value?
PCB fabs apply etch compensation — traces are drawn wider than designed to account for etching that makes finished traces narrower. They also measure actual dielectric thickness post-lamination (it compresses). Typical causes of discrepancy: dielectric constant varies ±5% batch-to-batch for FR-4, copper roughness adds ~0.1–0.3 Ω at microwave frequencies, and fabs often use their own field-solver (not Hammerstad-Jensen). Always specify impedance on fabrication notes and confirm with a coupon measurement.
What trace width gives 50 Ω on standard 1.6 mm FR-4?
On 1.6 mm FR-4 (εr ≈ 4.3) with 1 oz copper (35 µm), a microstrip on the top layer sees a dielectric height of about 1.55 mm (subtracting copper). This gives approximately 2.9–3.1 mm for 50 Ω. Use this calculator with substrateHeight = 1.55 mm, dielectricConstant = 4.3, copperThickness = 35 µm and adjust traceWidth to confirm.
How does soldermask affect microstrip impedance?
Soldermask adds a thin dielectric layer (typically 20–30 µm, εr ≈ 3.5) over the trace, slightly reducing impedance — typically 1–3 Ω for standard microstrip. Most fabs account for this in their process calibration. If soldermask is a concern at your frequency (generally above 5 GHz), strip it from critical RF traces or use stripline instead.
Microstrip vs stripline: when should I use each?
Use microstrip for single-layer routing, easy tuning, and lower fabrication cost — but it radiates more and has higher dispersion. Use stripline (trace buried between two ground planes) when you need lower radiation, better isolation between layers, or tighter impedance tolerance. Stripline has ~40% higher loss per unit length (both planes act as lossy boundaries) but eliminates radiation. At 10+ GHz, stripline's lower dispersion is significant.
References
Transmission Line Design Handbook · Microwave Engineering, 4th ed.
- Transmission Line Design Handbook — Brian C. Wadell, Artech House (1991), Chapter 3 — Microstrip
- Microwave Engineering, 4th ed. — David M. Pozar (2011), Chapter 3.8 — Microstrip and effective permittivity
Shop Components
As an Amazon Associate we earn from qualifying purchases.
- SMA ConnectorsStandard SMA RF connectors for board-to-cable connectionsAmazon →
- RF Coaxial CablesCoaxial cable assemblies for RF signal routingAmazon →
- TinySA Spectrum AnalyzerCompact handheld spectrum analyzer for RF measurement up to 960 MHzAmazon →
- FR4 Copper Clad LaminateDouble-sided FR4 boards for RF prototype fabricationAmazon →
- PCB Manufacturing (JLCPCB)Affordable PCB fabrication with controlled impedance optionsJLCPCB →